Making Candle Holders Out Of Spindles. This is a great way to recycle and reuse old materials around the house. Saw the spindle off, reserving the prettiest part for your candle holder.

How to Make Spindle Candlesticks from an Old Chair Spindle crafts from www.pinterest.com

Align the three pieces, stacking the 4×4 and 6×6 post caps and placing the baluster on top. Also, they make great gifts! All you need are some scraps of plywood, mod podge, and paint, then stack them in different sizes.

I Always Caulk Because It Makes A Much Nicer Finish To Paint.

Make your own set of diy scrap wood candle holders. Reluctantly i cut them into shorter pieces trusting my project would work out. You can use them as beautiful wedding decorations and centerpieces!

Align The Three Pieces, Stacking The 4X4 And 6X6 Post Caps And Placing The Baluster On Top.

I found that a couple of my spindles were too tall, so i needed to chop them down. Ad by paulabclutterjunkie ad from shop paulabclutterjunkie. Also, they make great gifts!

While Doing This, Just Be Careful Not To Fill In The Nooks And Crannies.

You may need to sand the entire leg if the paint is chipped. How to make distressed candlesticks from old spindles found at a thrift storetake old spindles found at a thrift store and repurpose them into beautiful dist. Now, use the color fluff and your chip brush to coat your topper and spindles with a base coat.

Using A Drill, Place A Hole In The Top Of The Baluster About 1 Inch In Width, And 2 Inches Deep.

Here, a 1×5, 1×4, part of a staircase spindle, and the top (finial) of an old chair make up a great diy spindle candlestick. You can also place these candle holders in your outdoor garden while sitting with your family to get a relaxing vibe. This is a great way to recycle and reuse old materials around the house.

Saw The Spindle Off, Reserving The Prettiest Part For Your Candle Holder.

I sanded the rough edges, and cleaned up all the saw dust. After that, i did a little sanding, priming, painting, and then sanding again to distress the finish. Once they were assembled, it was a creative free for all.

Making Candle Holders Out Of Spindles. This is a great way to recycle and reuse old materials around the house. Saw the spindle off, reserving the prettiest part for your candle holder.

How to Make Spindle Candlesticks from an Old Chair Spindle crafts from www.pinterest.com

Align the three pieces, stacking the 4×4 and 6×6 post caps and placing the baluster on top. Also, they make great gifts! All you need are some scraps of plywood, mod podge, and paint, then stack them in different sizes.

I Always Caulk Because It Makes A Much Nicer Finish To Paint.

Make your own set of diy scrap wood candle holders. Reluctantly i cut them into shorter pieces trusting my project would work out. You can use them as beautiful wedding decorations and centerpieces!

Align The Three Pieces, Stacking The 4X4 And 6X6 Post Caps And Placing The Baluster On Top.

I found that a couple of my spindles were too tall, so i needed to chop them down. Ad by paulabclutterjunkie ad from shop paulabclutterjunkie. Also, they make great gifts!

While Doing This, Just Be Careful Not To Fill In The Nooks And Crannies.

You may need to sand the entire leg if the paint is chipped. How to make distressed candlesticks from old spindles found at a thrift storetake old spindles found at a thrift store and repurpose them into beautiful dist. Now, use the color fluff and your chip brush to coat your topper and spindles with a base coat.

Using A Drill, Place A Hole In The Top Of The Baluster About 1 Inch In Width, And 2 Inches Deep.

Here, a 1×5, 1×4, part of a staircase spindle, and the top (finial) of an old chair make up a great diy spindle candlestick. You can also place these candle holders in your outdoor garden while sitting with your family to get a relaxing vibe. This is a great way to recycle and reuse old materials around the house.

Saw The Spindle Off, Reserving The Prettiest Part For Your Candle Holder.

I sanded the rough edges, and cleaned up all the saw dust. After that, i did a little sanding, priming, painting, and then sanding again to distress the finish. Once they were assembled, it was a creative free for all.